Bobcat Skid Steer Won’t Start? It Might Be Locked, Not Broken
Some links here are affiliate links — if you buy through them, Dirt Road Mechanic earns a commission at no extra cost to you. It never affects which parts or tools we recommend. Full disclosure.
When a Bobcat skid steer won’t start, the cause is often something a tractor owner would never think to check. Bobcat builds security, interlock, and diagnostic systems into its loaders that change where the search should begin. A few of the most common no-starts have nothing to do with the engine at all.
A Locked Panel or a Remote Shutoff
The S205 and T190 manuals say keyless-panel loaders leave the dealer in locked mode, and a password is needed to start the engine. The dealer gives the owner a code, and behind it sits a permanent factory master password. On a used machine, a code the last owner never passed along leaves the loader dead until a dealer resets it. Panels fail too: a 2020 T76 owner on TractorByNet reported a screen that booted but wouldn’t take his password.
In June 2024, Bobcat added Remote Engine Disable to its Machine IQ telematics on select skid steers and track loaders. Once an owner or rental dealer sends that command, any start attempt fails, and a running machine drops into derate. If a rented, financed, or newly bought loader refuses to start with no codes and good voltage, call the dealer before testing anything.
What the Seat Bar Actually Controls
Tractor owners go straight for the seat switch. On the Bobcat loaders whose manuals spell it out, the seat bar and PRESS TO OPERATE LOADER button gate lift, tilt,t and drive, not the starter. The S250 manual even describes a traction lock override that only works with the bar up and the engine running, and an S70 owner on Heavy Equipment Forums noted his safety equipment only disabled the hydraulics.
If the engine runs but nothing moves, the skid steer hydraulic problems guide picks up from there. Seat bar sensor faults show as codes 11-05 and 11-06. One overlap matters: per the S205 manual, low system voltage (03-09) can also lock out lift, tilt,lt and traction, so a tired battery can pass for an interlock fault.
Codes 13 and 14 Point at the Fuel Solenoid
Bobcat’s codes split the fuel shutoff solenoid into its two circuits: 13-05, 13-06 and 13-07 cover the hold side (short to battery, short to ground, open), and 14-02 and 14-03 cover the pull-in side. A TractorByNet owner whose 2002 S185 wouldn’t start got 13-07 and 18-06. He was told the fault was the solenoid or its small jumper harness, and to buy the updated solenoid that eliminates the jumper.
The part number depends on the machine. Bobcat lists solenoid 6681513 for the 751, 753, 763, 773, S150 through S185, and T190. Solenoid 6689034 covers the bigger machines, including the S250, S300, S750, S770, S850, T300, and T770. Bobcat’s own parts listing for 6681513 says to check the wiring at the engine harness connector before plugging in the new one. Before buying either, put a Fluke 115 multimeter on the connector with the key on. Voltage at the plug and no movement points at the solenoid. No voltage sends you back up the harness, using the voltage-drop checks in the tractor electrical problems guide. Codes not listed here can be looked up on Bobcat’s fault code page with the machine’s serial number.
The Pickup Tube That Breaks Off Inside the Tank
On older Bobcats, a Heavy Equipment Forums administrator calls the in-tank fuel pickup tube a very common repair. Early machines used flexible tubing with a strainer and check ball on the end; later ones went to stiffer plastic without them. When the tube cracks or falls off its elbow, the engine runs on a full tank and starves as the level drops, as an 863 owner there described. A collapsed primer bulb is another sign, which a 763 owner on TractorByNet traced to a stuck check ball.
Don’t blow compressed air back down the fuel line. A Bobcat mechanic on the same forum warned it knocks the pickup tube off on machines with the check ball, and a 963 owner on TractorByNet learned that the hard way. The fix is cheap. FridayParts lists pickup screen kit 6650239 for the 751 through 873 at $13.80, and an 873 owner reported $26 at the Bobcat counter for a new tube and fuel line. Use a new grommet every time.
Newer Engines Fail Differently
Starting with its Tier 4 loaders around 2014, Bobcat moved its 500 through 800 frame machines from Kubota engines to its own Doosan-built engines. These are common-rail engines, so the pattern shifts to rail pressure. On Heavy Equipment Forums, a 2016 T630 owner got a low rail pressure code after a fuel filter change, and a 2018 S570 owner got one after a coworker cranked it before priming. A reply in the T630 thread said injector failures are common on these engines and pump failures are rare. Bobcat’s R-Series brochure lists a self-priming fuel system, but on older common-rail machines, prime before you crank.
Cold Mornings Have Their Own Rules
The T190 manual and the S205 manual forbid ether with glow plug systems because it can explode. The glow plugs cycle on their own; wait for the icon to go out before pressing start, and if the plugs themselves are suspect, the glow plug testing guide covers the relay and meter checks. Below −15°F, the keyless display can take 30 seconds to several minutes to become readable. Below −20°F, warm the hydrostatic oil before starting, then run the engine for at least five minutes before working. Block heater fitment and fuel gelling have their own guides. A low-voltage code on a cold morning usually means the battery needs a real charge from something like a NOCO Genius 10 before anything else gets replaced.
What to Get From the Seller of a Used One
Get the owner password in writing, and watch the seller enter it and start the machine cold. Ask whether the loader has Machine IQ and whether the subscription is being cancelled or transferred, so nobody can disable it from an old account. Write down the serial number, because solenoid and pickup tube parts change by serial range. If the listing is a Bobcat CT compact tractor rather than a loader, it’s a different machine built by Kioti’s parent company, and the Kioti tractor no-start guide is the better reference.
Most of the time, a Bobcat skid steer that won’t start comes down to a password, a voltage problem, or a fuel solenoid circuit, not a failed engine.
Two Quick Answers
How do I get the password for a used Bobcat? Ask the seller first. If the owner code is lost, a Bobcat dealer can use the factory master password to get in and set a new owner code.
What does code 13-07 mean? It points to an open circuit on the fuel shutoff hold solenoid. Check the connector and the jumper harness before buying the solenoid itself.






